trinityamps.com

Trinity Amps Guitar Amp Forum
It is currently Thu Oct 31, 2024 7:46 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
PostPosted: Wed Jun 19, 2019 2:20 am 
Offline
Expert
Expert

Joined: Sat Dec 04, 2010 3:42 pm
Posts: 519
Location: Qualicum Beach, BC
Yes, they are! It's like a normal diode. There's usually a band around one end and that's the cathode. On the schematic symbol the cathode is the zig-zag line at the point of the triangle. Connect the banded end to the gate on the Mosfet.


Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 7:06 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
mitch m wrote:
Yes, they are! It's like a normal diode. There's usually a band around one end and that's the cathode. On the schematic symbol the cathode is the zig-zag line at the point of the triangle. Connect the banded end to the gate on the Mosfet.

Thanks, Mitch! I think I've got the board populated except for most of the fly leads now.


Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 7:54 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Ok, here's up to date pics. I know the 10k c.f. resistor goes from the ground lug to pin #2 on the 12ax7 socket, but can't find where the 270 ohm 1/2 watt goes. And, I found the 10k 2w MO I thought was missing. I had it on the board. If anyone sees anything amiss, please speak up, I'm still a newb at this!!


Attachments:
IMG_20190619_070940.jpg
IMG_20190619_070940.jpg [ 2.2 MiB | Viewed 11667 times ]
IMG_20190619_070919.jpg
IMG_20190619_070919.jpg [ 2.72 MiB | Viewed 11667 times ]
IMG_20190619_070907.jpg
IMG_20190619_070907.jpg [ 2.34 MiB | Viewed 11667 times ]
IMG_20190619_070902.jpg
IMG_20190619_070902.jpg [ 2.8 MiB | Viewed 11667 times ]
File comment: The blue wire going in thru the speaker jack is a fly lead, I tucked it in there till I get back to soldering tomorrow.
IMG_20190619_070858.jpg
IMG_20190619_070858.jpg [ 2.21 MiB | Viewed 11667 times ]
Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 7:13 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
Yes, the one I got with my Tramp was a glassy looking orange color with a dark band on one end. The black band is equivalent to the silver band on the black 1N4007 diodes. The band determines the polarity or direction of current of a diode. The black band should be toward the gate (G) on the VRM eyelets as shown in the Layout drawing. Hope you found the diode and that this helps.

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 7:24 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
The only place I see that uses a 270 ohm on the layout is on the terminal strip for LED indicator lamp near the Power and Master Volume controls at front of chassis.

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 10:51 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Here's the board, my phone died earlier before I could upload all of em. Trying to take close up, detailed pics for you guys to check my work, and if I'm right, for future builders to reference.


Attachments:
IMG_20190619_070721.jpg
IMG_20190619_070721.jpg [ 2.07 MiB | Viewed 11656 times ]
IMG_20190619_070729.jpg
IMG_20190619_070729.jpg [ 1.64 MiB | Viewed 11656 times ]
IMG_20190619_070734.jpg
IMG_20190619_070734.jpg [ 2.2 MiB | Viewed 11656 times ]
Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 10:56 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Hankules wrote:
The only place I see that uses a 270 ohm on the layout is on the terminal strip for LED indicator lamp near the Power and Master Volume controls at front of chassis.


The red, purple, Brown carbon film resistor in the first pic, is it not a 270? The one in the bag.


Top
 Profile  
 
PostPosted: Wed Jun 19, 2019 10:59 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
By the way, just wanna say thanks to anyone commenting. I love building amps, and your help is much appreciated!!


Top
 Profile  
 
PostPosted: Thu Jun 20, 2019 12:50 am 
Offline
Expert
Expert

Joined: Sat Dec 04, 2010 3:42 pm
Posts: 519
Location: Qualicum Beach, BC
The pictures look good. I didn't check to make sure all the parts are in the right place, but I didn't see any glaring mistakes.

Red-purple-brown is 270 ohms. Like Hankules said, the only place I see a 270 ohm resistor on the schematic and the layout drawing is on the LED serving as the pilot light.


Top
 Profile  
 
PostPosted: Thu Jun 20, 2019 3:49 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
The one I have definitely came with the kit, but it's a good bit larger than the one for the power indicator light. I labeled all of them when I first opened the kit, except the ones for the vrm. It still has the label on one lead. But, everything I need is there now, and almost all installed.


Top
 Profile  
 
PostPosted: Thu Jun 20, 2019 5:15 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
Epi, please post pics of interior, front panel and the resistor. There should be a terminal strip near the pilot light and should have one end soldered to a lead on the LED and the other to the terminal strip. with every thing connected , it should look like the picture on page 30 of the build guide. There is only one (1) 270 ohm resistor listed in the Bill of Materials (BOM). Also, you might consider going to the Tramp support page and downloading the COLOR, PDF build guide if you haven't already. Steven prints the one that come with the kit in black and white, the color guide made it easier for me to pick out some details

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Thu Jun 20, 2019 5:42 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
http://www.searchingtabs.com/rcolor/rescolor.htm Also, I have found this very helpful for verifying resistor codes.You may want to use it if you build another amp in the future.

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Fri Jun 21, 2019 3:32 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Thanks, guys. I downloaded the color guide, and will post pics soon.


Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 3:08 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Ok, I figured out where my zener diode got lost at... I used it in place of the 270 ohm for the l.e.d. I had a snafu removing the zener diode, and broke a lead of the led, so now I gotta order a new one of those. Good thing is, I know what I did wrong!


Attachments:
15611871625851809660755.jpg
15611871625851809660755.jpg [ 2.32 MiB | Viewed 11624 times ]
Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 3:59 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
As of now, most fly leads aren't connected yet, but I'm working on em. Here's the current state.


Attachments:
1561188653129119870035.jpg
1561188653129119870035.jpg [ 2.1 MiB | Viewed 11623 times ]
1561188977855576180010.jpg
1561188977855576180010.jpg [ 2.35 MiB | Viewed 11623 times ]
1561189202602-1374447688.jpg
1561189202602-1374447688.jpg [ 2.57 MiB | Viewed 11623 times ]
1561189843695857564227.jpg
1561189843695857564227.jpg [ 2.81 MiB | Viewed 11623 times ]
Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 4:01 am 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
Coco, is there a special type of led, or can I just order any old led from internet?


Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 3:05 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
BOM indicates: LED RED 5mm, 10 mA. So you need a 5 millimeter diameter red LED rated for 10 milliamps. Actually any color is fine, just make sure the diameter and milliamp rating are correct.

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 3:34 pm 
Offline
Experienced
Experienced

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 374
Location: Shawnee, OK
Epi, looked on Amazon, they want to sell you whole kits. Most were rated at 20 mA, so you might check w/ Coco and see if they will work.

_________________
"The only problem with being retired is you never get a day off"


Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 4:56 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
I was looking for the mA rating, I'll order em asap!! I wonder how blue would look....


Top
 Profile  
 
PostPosted: Sat Jun 22, 2019 5:08 pm 
Offline
Friend
Friend

Joined: Tue Apr 23, 2019 6:46 am
Posts: 27
What's the reverse current rating mean? I found the 20mA led's, & some say the max reverse current is 10mA. Does that mean they'll work?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group