trinityamps.com

Trinity Amps Guitar Amp Forum
It is currently Mon Jun 17, 2019 9:14 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 18 posts ] 
Author Message
 Post subject: Eyelet Board Question
PostPosted: Fri Apr 12, 2019 8:34 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
Wondering if I have an extra eyelet on my board. The layout doesn’t show the eyelet by my finger in the picture below. Can I just skip it, or am I supposed to do something with it?

Thanks


Attachments:
C0C675DB-B46A-4E00-B200-DEE5777F15FE.jpeg
C0C675DB-B46A-4E00-B200-DEE5777F15FE.jpeg [ 1.81 MiB | Viewed 668 times ]
4C2F4120-68DE-42AA-AAC0-30D2E0F502DF.jpeg
4C2F4120-68DE-42AA-AAC0-30D2E0F502DF.jpeg [ 2.7 MiB | Viewed 668 times ]
Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 10:01 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Looks like a 390R resistor, a small capacitor, and and green jumper go to it, if I'm looking at the right spot where you're pointing on the board. Might look at the layout again. Some times a break will let you see things that you might have missed.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Last edited by Hankules on Fri Apr 12, 2019 10:08 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 10:05 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
PS Looking again, you might also have the green jumper in the wrong eyelet.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 10:27 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Also, check the value of the resistor where connects to last orange drop cap at the top. Make sure it's a 24K ohm and it should run down to where the (2) 1M ohm and the 820 cap connect.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 10:34 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Was that any help?

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 11:29 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
Definitely helpful. I put it away for the night, I’ll take a look at it tomorrow and see if I can figure it out. Thanks for all the insights!


Top
 Profile  
 
PostPosted: Fri Apr 12, 2019 11:53 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
You're welcome. Lotsa of stuff going on in that area. You picked a pretty complicated build, I'm not trying the OSD or the TripTop until I get a few more builds done. Right now, the Tramp is frustrating me!

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 3:56 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
Ok, here are a couple more pics. The eyelet in question is shown on the jumper layout in the builder’s guide, but it isn’t on the layout. It looks like it would be directly under the .022 cap.


Attachments:
BE1A1F1C-151B-4C9E-8FA4-580C36F0C5E9.jpeg
BE1A1F1C-151B-4C9E-8FA4-580C36F0C5E9.jpeg [ 3.31 MiB | Viewed 650 times ]
54901B34-7574-48D9-A4D7-779B3FABF449.jpeg
54901B34-7574-48D9-A4D7-779B3FABF449.jpeg [ 2.66 MiB | Viewed 650 times ]
Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 4:00 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
It lols like it’s connecte to the .022 cap in this picture from the sod amp page on trinity website. Maybe I just jumper it across to the eyelet at the top of the board?


Attachments:
16AE69DE-83A7-485A-BC40-B37F0B1FF750.png
16AE69DE-83A7-485A-BC40-B37F0B1FF750.png [ 7.75 MiB | Viewed 650 times ]
Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 5:23 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
download/file.php?id=2203&mode=view This build by a guy in Bangkok has a good view of a stuffed board. Looks like he had enough lead on the .022 cap to just pass over the eyelet in the center. You might want to look at his post. I think stuffing the board will get easier as things progress. If you get really get stuck you can PM Stephen (Coco) using the User Control Panel (upper right hand corner of forum page). Again, I haven't built the OSD and am offering what little insight I have.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 5:32 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
That is exactly what I neede to know. Thanks for all your help!


Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 5:34 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Check page 61. There may be under board leads connecting to the center eyelet? But I don't see one on the layout. Also, don't think holes to run leads would have eyelets in them.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 5:54 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
You're welcome. Always willing to share what little I have learned.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Sat Apr 13, 2019 5:59 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Found this site to be helpful. http://www.searchingtabs.com/rcolor/rescolor.htm I book marked it on my browser.

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Sun Apr 14, 2019 7:55 am 
Offline
Holy Ghost
Holy Ghost
User avatar

Joined: Sun Mar 13, 2005 4:10 pm
Posts: 7317
Location: Brighton, Canada
It's extra. You can solder to it and jump to the outside lead or solder to the outside lead and ignore it like in the layout.

_________________
Stephen
Web: www.trinityamps.com. Facebook: facebook.com/trinityamps. Twitter: @trinityamps


Top
 Profile  
 
PostPosted: Mon Apr 15, 2019 5:12 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
Build going well? :D

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
PostPosted: Tue Apr 16, 2019 10:44 pm 
Offline
Friend
Friend

Joined: Thu Mar 28, 2019 10:57 pm
Posts: 12
Build is going pretty good, thanks. I messed up checking voltages and fried my rely board, so I’m back to waiting on U S Customs.

Hoping to crank it out quickly once I get the new board from Stephen!


Top
 Profile  
 
PostPosted: Mon Apr 29, 2019 9:59 pm 
Offline
Novice
Novice

Joined: Wed Sep 12, 2018 5:17 pm
Posts: 114
Location: Shawnee, OK
May have to order a OT for my Tramp! If I fried it, I'll be waiting on Customs, too!

_________________
"You can always tell a German, but you can't tell 'em much!" ( Momma Ruth)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group